Maxx FBL Combo - Unit + Prog.Box
Special price for the market launch !
With the aim to build the best flybarless system at affordable price, MAXX flybarless unit is designed with most advanced MCU gyro and 6-axis sensors to deliver best performance and full features at the price everyone can afford. Designed by a team of pilots with years of experience and tested by best pilots in the world, this MAXX flybarless system not only brings affordable flybarless units but also the most innovative product to the market.
Vibration Resistant :
MAXX Flybarless System uses newest technology sensors with high sample, high resolution and low thermal offset drift. The flybarless unit is very vibration resistant and very stable in flight for any size of helicopter.
Easy setup with MAXX Software. Customers can use mLink port for connection to MAXX setupcard and MAXX ecosystem in the future.
MAXX flybarless system brings a feeling of good flying with the default setup, reducing the first setup time. Especially the new tail control algorithm offers good tail control with default setup on all helicopter kits.
Ability to change tail gain on the transmiiter (CH5) and on MAXX software.
Ability to customize Cyclic, Tail PID gain according to more flight styles and mechanical difference of each helicopter.
DSM2/DSMX Satellite, S-Bus Ready , SRXL, SUMD, JR-SBUS Mode B, and PPM receiver .
Offering the convenience of satellite technology, the MAXX flybarless supports Spektrum DSM2 & DSMX satellite receivers, S-Bus technology via Futaba
Dual Satellite Port:
The MAXX flybarless has Dual Satellite Port providing more reliability for large helicopters and long range flights, ability to BIND by MAXX software
Built-in Electric and Nitro Governor:
MAXX active throtle compensation is calculated according to cyclic, collective, tail, RPM and other status of Flybarless units. It offers very stability in RPM and more powerful, more efficiency compared to other governors.
Nitro Governor: MAXX flybarless supports Governor for Nitro Helicoper, using magnetic RPM sensor connect to RPM in pin of unit. Minimum 7 chanels on transmitter is required for Nitro Governor. The throtle chanel is set up to V-shape for fast respone. RPM is decided by CH7 (AUX2) channels on TX, max value 1920us for max Rpm setting and not decided by throttle chanel
Electric Governor: Use RPM wire output of Esc or RPM sensor connect to RPM input pin . Minimum 6 chanel transmitter is required for electric governor
Event Logging and High sample rate Vibration logging:
The memory of unit stores data of 5 last flights.
Event logging: Time of Radio signal, motor run/stop , BEC voltage drop
Vibration logging : Ability to review the vibration level when flying by graph form on the MAXX software
No more manual adjust for swashplate. With MAXX flybarless, there is no need to spend a lot of time to balance the swashplate. The software can detect unbalance of swashplate in piro hover flight and autotrim the swashplate.
Push button on the MAXX flybarless before flight
Take off and do a fast tail rate piro hover more than 10s. Land and push the button on the MAXX flybarless again; it will save the new swash trim value.
Rescue mode is activated when the helicopter tilt angle is over 25 degrees with ground and have event Gyro gain (CH5) value drops from high to below centre value (1520us). The helicoper will automatically flip back then automatically increase the height. Within 3 seconds the rescue mode will exit.
With advance accelerator sensors our MAXX flybarless system has the most accurate calculation for most accurate rescue. This saves a lot of crashes and a great tool for beginners to learn to fly.
Example: CH5 on Tx is 35% for flight, so you should be set CH5 on Tx is -35% (or 35% normal mode, not AVCS) for rescue mode , reaction of the tail will not change.
Drop Radio Signal Indicator:
The LED light on the MAXX unit will blink if detecting more than 50ms radio signal loss. This can be viewed in table Logger in the MAXX software.
Bec Drop Detector:
Nowadays, servos are very strong and getting stronger, many crashes are due to weak BEC or bad connection. With MAXX flybarless, there is no more worries about this. Introducing an innovative feature: BEC Drop Dectector that helps prevent many crashes. MAXX flybarless keeps reading voltage of BEC continuously before and during flight, if BEC is weak and voltage drops over 0.5V, the red LED on MAXX flybarless unit will double flashed to inform pilot the problem. The problems are also logged and viewed in table logger in MAXX software for reference.
||36mm x 28.5mm x 15mm (LxWxH) / 18g
||Any helicopter size, Nitro and Electric Compatible
||PPM / Futaba S-Bus / Dual Spektrum DSM2 & DSMX Ports / SRXL/ SUMD/JR-XBUS Mode B receivers
|Cyclic Servo Support:
||Analog and Digital 1520uS
|Tail Servo Support:
||760uS / 1520uS – Up To 560Hz Frequency
||3.6 – 8.4V
MAXX Program Card
Full configuration for MAXX Flybarless without a computer
- Battery meter: 2 -6s battery voltage meter of the cell and total voltage.
- Rx signal monitor: checking Rc channel value of the 7 channels, checking the center of transmitter.
- Heli configuration: Heli size, flying style, receiver type, DSM satellite Bind, resuce function, safety threshold of the BEC, sensor mount type…
- Cyclic configuration: Swashplate type config, swashplate Trim, servo type, servo Trim, servo reverse,
- Cyclic tunning: Limit, cyclic gain, separate aileron gain and elevator gain setting, agiity, roll/flip rate, advance PID gain, RC deadbank, Eleprecom, paddleSim, expo, change value of three banks..
- Collective configuration: Pitch travel +/-, direction, pitch pump
- Tail configuration: Servo type, servo reverse, tail travel, tai servo Trim, tai balancer for 2-ways tail rotation brake, tail rotation rate, tail acceleration , tail stop, show the tail gain from Tx, tail precom ( by collective pitch, cyclic), tail PID advacne gain tunning.
- Governor configuration: governor enable/disable, governor type (Gas nitro/ electrics), 10-step gain, Max-min of Throttle, start throttle for Maxx softstarter, scrollup speed for softstarter, gear ratio configuration, poles, Bailout, Idling bailout, set Rpm value of three banks.
Ability to configurate 760us swashplate type servos